If you have a Netgear Orbi router, the status of its operation is indicated by a series of lights. If, however, the wireless device’s LED is flashing purple, you’re in deep trouble. Not to worry, though, because help is on the way. This post contains some of the greatest troubleshooting advice available, and it should have you ridding your Netgear Orbi purple light problem in no time. In such a case, please continue reading below.
Table of Contents
If you have a Netgear Orbi router, the status of its operation is indicated by a series of lights. If, however, the wireless device’s LED is flashing purple, you’re in deep trouble. Not to worry, though, because help is on the way. This post contains some of the greatest troubleshooting advice available, and it should have you ridding your Netgear Orbi purple light problem in no time. In such a case, please continue reading below.
However, before we fix the problem, let’s investigate what could have caused it. Listed below are some of the most often cited causes of the Orbi purple light problem:
- You have neglected to update the firmware on your Netgear Orbi.
- Your router’s Ethernet connection to your modem seems shaky.
- Your Orbi device’s hardware is malfunctioning.
- Your Netgear Orbi router and modem are too far apart.
- Even if you try to avoid it, technical difficulties may eventually force you to deal with the Orbi purple light problem.
Now that you know what’s causing the purple orbi light on your Netgear, you can try our solutions.
What Does Orbi Purple Light Mean?
The light on your Netgear Orbi showed how strong the signal was and what its status was. On a good day, you’d see a blue light that went out. But what does it mean when a light is purple?
Your Orbi’s purple light can only mean two things:
You can’t connect your device to the internet. Either the satellite is out of range or something is getting in the way of the connection.
You can’t connect your Orbilogin.com satellite to the router. When you try to sync and get a solid purple light, the process doesn’t work.
Check where the light is coming from on your device before you do anything else. Is it coming from the satellite or the router?
How To Fix Orbi Purple Light Steps
Restart Netgear Orbi to restore functionality
You should first try restarting your Netgear Orbi router. It’s the bare minimum, yet it usually solves the problem. This is how you may restart your Netgear Orbi router:
- Turn off and disconnect the power cord from your Orbi wireless router.
- The wait will be worth it.
- After that, reconnect your Orbi router to the wall and power it back on.
Now, see if you’ve fixed the purple light on your Netgear Orbilogin.com. If you are, please keep reading this article.
Update Orbi Firmware
Bugs and technical issues can be resolved by updating the Orbi’s firmware. It improves your wireless device’s efficiency overall, too. Since updating the firmware on a Netgear Orbi can affect many aspects of operation, this may fix the purple light problem. Don’t delay any longer; go to orbilogin.net to upgrade your Orbi’s firmware.
Check Ethernet Cable Is Still Connected
Your Netgear router’s Ethernet connection to the present modem is unstable. Perhaps the Ethernet wire you’re utilizing is damaged or worn down.
You should connect your WiFi devices with a new Ethernet wire or tape up the existing one as the first step in troubleshooting.
Turn off your WiFi Gadget
The Ethernet cable isn’t the only thing that can cause the purple light of death; if your Netgear Orbi router is too far away from the existing modem, it can’t communicate with it. As a result, ensure that your two gadgets are physically close.
It’s also bad to put electronics in a corner or near a solid wall.
If the Netgear Orbi purple light problem persists after troubleshooting steps, a factory data reset should be performed. Specifically, here’s what you do:
Best Ways To Reset your Netgear Orbi To its default settings?
With these steps, you can easily reset your Netgear Orbi wireless router.
- Find the Reset button on your wireless router.
- Carefully press it with an oil pin once you’ve located it.
- You should then sit tight for a while.
After resetting your Netgear Orbi to its original settings, you can reconfigure it by visiting the Netgear Orbilogin page.
To Sum Up
This concludes our tutorial on fixing the Orbi purple light. We hope the information on this page helped turn off the purple LED. Leave a remark expressing your gratitude if they did.
